Top information

Mine Surveyor

Open cut or surface mining in coal is a suitable choice when coal seams are closer to the natural surface It is an effective method of retrieving a higher proportion of coal when compared to underground mining...

2006G Volume 2

AIRBLAST CONTROL TECHNIQUES IN OPEN CUT MINES Alan B Richards and Adrian J Moore Terrock Consulting Engineers Pty Ltd ABSTRACT Effective control of airblast requires that significant factors be identified and satisfied by blast...

Meridian Mining Services Open

Meridian Mining Services provides a range of professional services to the open cut mining industry We offer mining and civil project surveying, mine engineering, site supervision and project management and sales, installation, management, support, and rental for the deformation monitoring system...

H BLASTING IN SURFACE EXCAVATION

Cast blasting is the controlled placement of overburden into the previously mined cut resulting in a reduced volume or overburden material for the dragline to handle...

Engineering Geology Field Manual

BLAST DESIGN Introduction This chapter is an introduction to blasting techniques based primarily on the Explosives and Blasting Procedures Manual (Dick et al, 1987) , The open corner at the left of figure 19-2 is preferable Given the dominant jointing in ,...

open pit mine blasting

Nov 29, 2010· Licensed to YouTube by UMG (on behalf of Universal/Island Def Jam); UBEM, UMPI, CMRRA, UMPG Publishing, Warner Chappell, Wixen Music Publishing, ASCAP, and 3 Music Rights Societies Show more Show less...

Chapter 8 BLAST DESIGN

Chapter 8 BLAST DESIGN (Figure 8-2) Staggered pattern , follows (Figure 8-4) shows a typical bench cut with two free faces and fired with one delay per row , Figure 8-5, the rock mass would be thrown to the right during blasting (Figure 8-4) Typical bench cut with two free faces and fired with one delay per row (Figure 8-5) Direction of ....

NOx emissions from blasting operations in open

Quantitative measurements of NO 2 in plumes from blasting were made at two open-cut min The results showed that NO 2 was present in most of the plumes but in relatively low concentrations (typically ranging between 0 and 7 ppm)...

Underground mining (hard rock)

Declines can be a spiral tunnel which circles either the flank of the deposit or circles around the deposit The decline begins with a box cut, which is the portal to the surfaceDepending on the amount of overburden and quality of bedrock, a galvanized steel culvert may be required for safety purpos They may also be started into the wall of an open cut mine...

Drilling and Blasting in Open

From Introduction: "The drilling and blasting practices described in this bulletin are chiefly those in use at the time of these visits Information, obtained by correspondence, on recent changes at certain mines is also included The bulletin is confined to descriptions and comparisons of drilling and blasting methods at the six open-cut min"...

Straitline Drilling

We specialise in Open Cut drilling operations with a team of highly skilled Drillers Our crews can handle even the most complex patterns, have the ability to work to Engineers specifications and can adapt to an ever-changing mining environment...

Techniques of Controlled Blasting

Following are the techniques of controlled blasting: Line drilling, Trim (Cushion) blasting, Smooth (contour or perimeter) blasting, Pre-splitting, Selecting and employing various parameters of blast design, using modern technology, Precise and accurate timing delays, Muffle blasting at critical and congested areas...

BLAST MANAGEMENT PLAN 2012 2015

It encompasses blast management across both the Integra Coal Open Cut and Integra Coal Underground Sites, collectively known as the Complex Current and approved operations within the Complex include the North Open Cut, the Underground...

Open Cut Blast

Feb 07, 2008· What can go wrong when you use too much explosive Have a good look at the shovel and drill parked in the wrong place...

Safety Policy and Procedure

41 Abrasive Blasting: Abrasive blasting is the most common surface preparation technique used to remove old paint and other surface materials such as rust, mill scale, dirt, and salts In abrasive , must be held open manually A support shall be provided on which the nozzle may...

Drilling and Blasting in Open

From Introduction: "The drilling and blasting practices described in this bulletin are chiefly those in use at the time of these visits Information, obtained by correspondence, on recent changes at certain mines is also included The bulletin is confined to descriptions and comparisons of drilling and blasting methods at the six open-cut ,...

Integra Coal Operations Pty Ltd

BLAST MONITORING PROGRAM - 1 - INTEGRA COAL OPERATIONS PTY LTD Integra North Open Cut Coal Mine Report No 642/10c R W CORKERY & CO PTY LIMITED 1 INTRODUCTION The Integra North Open Cut Coal Mine (the North Open Cut,...

Mine Surveyor

Volume Calculations (Open-cut Mine Surveying Duties) Volume calculations are very important in mining to not only estimate the efficiency of machines and mining methods, but also to determine how much contractors should be ,...

NO x emissions from blasting operations in open

A study has been carried out to introduce a new approach for measuring the emissions of NOx gas by scanning and monitoring the resulting plume from blasting in open-cut ,...

ARblast: All Resources on Blasting

Rules, Regulations, Research and Resourc The Federal Surface Mining Control and Reclamation Act of 1977 requires that coal mine blasting be limited based on the site conditions so as to prevent: injury to persons, damage to public or private property outside the permit area, adverse impacts on any underground mine, and change in the course, ,...

Mining Photo

The above colour palette represent the primary colours that have been detected in the current image Click any of the colour boxes to search other images which contain that colour...

No.416 Jianye Road, South Jinqiao Area,Pudong New Area, Shanghai, China.

Telephone : +86-21-58386189, 58386176

FAX : +86-21-58385681